CU MILLBERA
Curled wire, not varnished.
Thickness over 1mm
Without ends
Material: thicker electrical wires
CU Piece
Scrap with a thickness exceeding 1 mm, without whitening, insulation, varnish, iron, other non-ferrous metals, grease and oil. No non-metallic impurities.
They can be pipes without whitewash, sheets and sheet metal scraps, flat bars, and oxidized milberry.
CU Stove+Pobial+Shavings
Matte, gray-silver, bluish patina.
It should be free of impurities, stainless steel and ZnAl
Stoves - Welding tips, in gas stoves
There must be no varnish, no tips, no tin, no impurities, no metals, no brass, no plastics.
Shavings - small thin pieces or shreds of metal,
up to 3% impurities.
CU Gleamlng
Thin electrical wires, flat pieces, rods, hair, flat bars, tubes, sheet metal.
Post-production.
It must be free of varnish, tips, tin, burnt, and other contaminants.
CU UNSORTED
Painted electric wires, motor windings, tin tubes, can be burned or soldered.
Non-metallic impurities up to 2%.
There must be no metals, plastic, rubber, whitewash, Fe, Al, other metals and impurities.
CU Coils
Wire cable wrapped with plastic or cotton insulation.
D0 8% impurities. CU above 90%
There can be no varnish, metal, brass or plastic.
MO Yelow
It may be in the form of rods, pipes, fittings, sheets, castings or other materials.
It must be free of scales and impurities.
MO Shavings
Small, thin pieces or shreds of metal.
It must be free from impurities, plastic and metal.
No humidity. Fe-free.
It cannot be magnetic.
.jpg)
N10 (thin)
Non-batch, thin steel
Wall thickness up to 4 mm
Length from 1m
Without foams, cotton wool and other contaminants.
MO White
There must be no contamination, stainless steel, ZnAlu, hoses or balls.
MO-CU Cooler
Mo-Cu coolers.
Car radiators, air conditioners, refrigerators, freezers, etc.
No metal, plastic, rubber, gaskets, disarmed, clean.
N2/W2 (medium)
Thickness min. 4mm
N2 - non-batch scrap with a length of more than 1 m
W2 - batch scrap with a length of up to 1 m
Without foams, cotton wool and other contaminants.
N5
Non-batch, thin steel
Wall thickness up to 1 cm
Length from 1m
Without foams, cotton wool and other contaminants.
Shavings
These are fragments of steel that are created during mechanical processing, such as turning, milling or drilling.
ZN Sheets
Scrap in the form of old and new sheets, also wire, goose, anode.
Cast iron, non-batch
It is a typical variety of cast iron, used in many different applications, such as the production of car parts, fittings, and machine elements.
Over 1m long.
Cast iron feeder
This is a type of cast iron obtained by a batch casting process, which means that the metal is cast in molds in batches from one batch of material in specific portions, rather than in a continuous process. Cast iron steel is widely used in industry, such as in the production of machine components, fittings, engine parts, etc.
Lengths up to 1 m.
ZNAL
Zincaluminum can be used in various applications, such as the production of car parts, structural elements, or in the electrical industry, carburetors, fuel pumps, furniture accessories, etc.
.jpg)
PB Clear
Pure Lead is a type of lead that is not oiled with other metals and free from contamination. It is a soft, heavy metal with a silvery-gray color. Pure lead is used in many different applications, such as the production of batteries, electric cables, pencils, and in the chemical industry for various processes.
CrNi 8% (stainless steel)
This means that this steel contains 8% nickel in relation to the total weight of the alloy. CrNi 8% alloy steel is often used in applications where high resistance to corrosion and oxidation is required, such as the chemical industry, the production of kitchen appliances, or the food industry. Thanks to the presence of chromium and nickel, this steel is also characterized by good mechanical strength and an aesthetic finish, which makes it a popular choice in many applications.
AL CU Cooler
It is a radiator made of aluminum and copper that is widely used in the automotive industry to cool vehicle engines. Aluminum is typically used for the radiator core, while copper pipes or plates are used for the coolant flow.
PB Battery
Batteries from cars and trucks
Without containers or metal casings.
WE DO NOT ACCEPT LITHIUM ION BATTERIES
CrNi Shaavings
CrNi alloy steel chips is a variety of stainless steel containing chromium (Cr) and nickel (Ni), in which the mechanical processing process produces chips.
It is a secondary raw material produced during mechanical processing of elements made of this steel.
AL Sector
Post-cable scrap of energy aluminum with a thickness exceeding 2 mm.
Non-oxidized, free from contamination with iron, other metals and aluminum alloys.
Non-metallic contamination and oil contamination are not allowed.
The class does not include granules.
Without wire with Fe in the middle.
AL Wire rope
Energy lines and rails.
There must be no contamination, fittings, other metals or alloys.
Without wire with Fe inside
AL Wheels
Clean rims.
There can be no weights, valves, Fe or plastics.
Truck rims.
AL Colored profile
Post-production pieces of scrap in the PA38 grade, with a thickness of over 0.5 mm and a length of up to 1 m.
Free from contamination with other metals and alloys.
Contamination with plastic, rubber, glue, foam, etc. is unacceptable.
Coated with varnish.
AL Offset
Offset sheet metal scrap containing min. 99% Al.
Post-production
It must not be contaminated with iron or other metals and alloys
.jpg)
AL White profile
They occur after dismantling window frames, door frames, balustrades, post-production.
Up to 1 meter long, thickness from 0.5 mm
Without screws, seals or plastics, varnishes, foam and other contaminants.
AL Mg piece of foil
In the context of aluminum-magnesium, it can be a material that is used in various applications such as the aerospace industry, the automotive industry, or industrial structures.
AL Sheet-Parrs
Post-production scrap and post-depreciation
Min 99% Al
There must be no paint, foil, glue, tar, plastic or rubber.
AL Plasticyty
Bicycle, truck, motorcycle rims, truck sides, curtain rod.
Up to 2% impurities.
AL Blinds
Scrap window blinds.
They must not contain strings or other impurities.
AL Casting
Clean casting or post-production
No dirt, no screws
Up to 2% impurities.
Aluminum casting waste: showers, overflows, product shortages, etc.
Amortization castings must be free from contamination with other metals and alloys.
AL Shavings
Clean bulk aluminum chips: turning, drilling, milling, sorted by aluminum-silicon alloy groups, cast or deformed.
AL Radiators
Coolers Al
Car radiators, air conditioners, refrigerators, freezers, etc.
No metal, plastic, rubber, gaskets, disarmed, clean.
AL Cans -5% humidity
Waste from the production of aluminum cans: offcuts, sheets, scrap, including those with a thin layer of varnish, without lids with a seal
Scrap drinks cans
There can be no foil, closed deodorants, or steel cans.
Up to 5% impurities.
Electric motors
They are found in many appliances such as: electric toothbrush, hair dryer, mixer, elevator, tram and car etc.
Free from sludge and other contamination.
.jpg)
Complete Combustion Engines
Complete combustion engines are usually assembled units that consist of many components, including the engine block, cylinder head, intake and exhaust system, fuel supply system, ignition system (in the case of gasoline engines), lubrication system, and other parts.
AL Contaminated min 30%
Contaminants may include other metals or substances that are not desirable in pure aluminum.
In some cases, lower purity aluminum may still be used in various applications, but may require additional processing or recycling to remove or minimize contaminants.
Electric motors up to 2 kg
They are found in many appliances such as: electric toothbrush, hair dryer, mixer, elevator, tram and car etc.
Free from sludge and other contamination.
Starter
A starter is an electrical device used to start an internal combustion engine.
It is a key element of the starting system in cars and other vehicles equipped with an internal combustion engine.
Alternator
An alternator is an electrical device used in vehicles equipped with combustion engines.
Carbide drills, milling cutters
These are cutting tools that are extremely durable and effective in machining high-hardness materials, such as metals or composites.
Brazing
Magnetic and non-magnetic
Materials from the dismantling of machine installations, structural elements or decorative objects.
Without pollution.
Carbide inserts
These are small inserts or tool inserts made of sintered carbide that are used in cutting tools such as milling cutters, drills, and lathe cutters. Cemented carbide is a material with high hardness and wear resistance, which makes these inserts effective tools for machining materials with high hardness, such as metal or composites. They are widely used in the metal, automotive, aviation and machinery industries.
Cable
It is a flexible, usually insulated electrical wire or assembly of wires used to transmit electrical energy or signals. Cables are widely used in a variety of applications, such as electrical power in buildings, power cables in electrical devices, signal cables in communication systems, and data cables in computer networks. They are available in various sizes, shapes and configurations depending on their purpose and application requirements.
We do not accept antenna cables.
It cannot have plugs, boxes, sockets, Fe.
Steel W7
Thickness from 1 cm
W 7 - batch scrap with a length of up to 1 m
Without foams, cotton wool and other contaminants.
Clean car harnesses
No computers, no fuse boxes.